感觉不是interface group 1吧

而应该是interface  link-aggregation 1

感觉应该是 interface link-aggregation  1



【 在 hiyachen1 (海燕在飞) 的大作中提到: 】
: 输入 interface group 1报提示信息:
: please pointed its interface
: 该怎么处理？
: ...................
--
FROM 220.191.249.*

端口归入汇聚组后， 端口的独立操作肯定不行了，要通过汇聚组来配置


【 在 hiyachen1 (海燕在飞) 的大作中提到: 】
: 汇聚组下再配置报错：
: % Interface gigabitethernet0/25 is a member of link-aggregation 1, command rejected.
: 先将0/25～0/27加入汇聚组1,配置完成后，show run
: ...................
--
FROM 220.191.249.*

没有其它命令了吗？     那link-aggregation 1下面呢？ 有哪些命令？


【 在 hiyachen1 (海燕在飞) 的大作中提到: 】
: 没有interface link-aggregation  1
: 查看帮助：
: sw1(config)#interface ?
: ...................
--
FROM 220.191.249.*

sw1(config)#link?
    link-aggregation      Configure Link Aggregation properties
    link-status-care      Care which type link-status change for the interface

sw1(config)#linkli
sw1(config)#link-agg
sw1(config)#link-aggregation ?
    <1-31>                Link Aggregation group ID
    load-balance          Load balance method

sw1(config)#link-aggregation 1 ?
    allow-individual-port  Allow individual interface in this Link Aggregation
                           group
    mode                   Link Aggregation mode
    <CR>                  

sw1(config)#link-aggregation 1 mode ?
    lacp                  Lacp mode
    manual                Manual mode

sw1(config)#link-aggregation 1 mode la
sw1(config)#link-aggregation 1 mode lacp
% Link Aggregation 1 has already exist
sw1(config)#link-aggregation 1 mode manual
% Link Aggregation 1 has already exist

【 在 leelou 的大作中提到: 】
: 没有其它命令了吗？     那link-aggregation 1下面呢？ 有哪些命令？
:
--
FROM 117.136.38.*

sw1(config)#link-aggregation 1
sw1(config-link-aggregation1)#?
    arp                   Command arp
    arp-check             Arp-check
    clear                 Command clear
    description           Link Aggregation interface description Information
    dhcp-snooping         Dhcp-snooping
    dot1x                 Configure dot1x parameters
    end                   Exit from configuration mode
    exit                  Exit from current EXEC mode
    frame-tag             Frame tag
    groupping             Send echo messages
    help                  Description of the interactive help system
    inner-priority-trust  Inner tag priority trust
    ip                    Internet protocol configure command
    ip-subnet-vlan        Configure ip subnet vlan attributes
    link-aggregation      Configure Link Aggregation properties
    lldp                  Lldp
    load-interval         Set load interval delay
    logging               Logging
    loopback-detection    Loopback detection
    mac                   Bind a filter based MAC address
    mac-address           MAC address learning
    mac-vlan              Configure mac vlan attributes
    map-table             QoS mapping table
    mvst                  Mvst
    ndsp                  Ndsp
    no                    Command no
    ping                  Send echo messages
    port-security         Security related command
    port-type             Configure interface uni or nni
    protocol-vlan         Configure  protocol vlan
    qos                   Command qos
    rapid-scan            Rapid link scan
    show                  Command show
    shutdown              Shutdown this interface
    spanning-tree         Spanning-tree configuration
    switchport            Configure one or more ports parameters
    traceroute            Trace route to destination
    ulpp                  UpLink Protect Protocol enable
    uni-isolate           Uni interface isolate
    vlan                  Configure vlan
            
sw1(config-link-aggregation1)#

顺便提一下，是迈普，不是思科，我只有两台迈普交换机、没有华三、华为、思科交换机，哪些资料都没有用
【 在 leelou 的大作中提到: 】
: 没做过思科的聚合组， link-aggregation 1之后直接回车呢，是不是到了另一个界面里？
:
--
FROM 117.136.38.*